High Speed Copper Plated Wire Drawing Machine

Fine copper wire drawing machine Automated Copper Wire Drawing Machine copper wire tinning machine copper rod drawing machine high speed copper plated wire drawing machine drawing of copper copper wire twisting machine copper drawing process copper drawing copper wire bunching machine

Description

High speed copper plated wire drawing machine introduction

This company produces LT9-450 continuous annealing line used with pull-plus double-disc received Continuous Annealing Line (or, as the nose unloading line) production model, the formation of the entire production line continuous operation, drawing machine from a copper rod into the line of direct pull 8.00mm Model copper wire.


copper rod breakdown wire drawing machine (450/LT9) 

number of dies:9

installed capacity:125KVA (Main motor:AC.110KW,spooler motor:15KW)

drive: frequency inverters

Dimension length 3000 * 1800mm Weight 6.5T width  

 Annealing mode DC-annealing, annealing the use of advanced low-voltage power supply high current power supply, the control system adopts microcomputer intelligent control, equipment operation more stable, the maximum speed of 8 m / sec.


Specifications

LT9-450Copper Large Pull with continuous annealing production line

copper rod breakdown machine;rod breakdown machine;8mm copper rod dawing machine

From 8mm to 1.78mm—3.30mm

copper rod input diameter:8mm,

output diameter: 1.78mm—3.30mm

production speed:480meters/s 

production capacity: 1200KG/hour

 

LT-15DieHigh-speed copper drawing machine Main technical parameters

Inlet wire diameter

3.00mm

Outlet diameter

0.5mm—2.90mm

Drawing number

15

Power

30KW

Maximum speed

600m/min

Fixed speed wheel diameter

350 mm

Hourly output

1000kg/h


LT-1200 large Pull continuous annealing line supporting equipment as follows

Actinomyces gantry frame wear die rolling machine 110KW motor control cabinet tip LT-9 mold copper big pull 

LT-1200 annealing machine LT-1200 cabinet annealing operation of the main electrical cabinet automatic double-disc MD-up Machine XB-600 like the nose and unloading-ray machine (also purchased) can store 1 tonne of copper wire used in the production line when a large single-core BV capacity pay-off.


OUR SERVICE

●We provide free technical service about casting parts and application issues.

●Free on-site touring and introduction of our factory 

●We provide process design and validation for free

●We can guarantee on-time delivery of samples and goods

●Close follow-up of all orders by special person and keep customers informed timely

●All after-sale request will be responded in 24 hours


Product process

1. Drive: Host straight line wire drawing machine, the first five heads power by the AC frequency motor through high-frequency joint narrow V-belts, spread by the hardened reducer to capstan. And the other six heads power by the AC frequency motor through two high-frequency joint narrow V-belt to capstan.

2. Brake: Clamp brake mounted on the motor pulley, quick stop or emergency stop wire drawing machine, which can effectively brake. Its role not only as a brake, but also to prevent the reel reverse brake, release the clip close to the solenoid valve control clamp brake cylinder.

3. Capstan: The material is ZG45 steel, surface is build-up welded, the  surface is brightness, smooth, wear-resistant surfacing height of 150mm, long service life; hub height of 150-200mm.

4. Drawing die box: Die box is welded structure, into two cavity. The guide roller is mounted into the side to ensure that steel wire can straight into the drawing die, die holder should be adjusted to wire tangent to enter the drawing rolls tuning roller installed at the entry end of the mold base tuning roll by a small cylinder put power, tuning the swing of the roller, so that the corresponding sensor output signal to fine-tune the speed of change. Tuning roller wire tension by adjusting the air pressure change, regulation range 0.15-0.6Mpa. The mold box is also equipped with a stirring device. Tuning roller side of the mold box, a gear reducer single-phase capacitance running motor through a sprocket, power passed to the stirring arm to stir the mold box, lubrication powder, without agglomeration affect lubrication.

5. Jump-mode device: When drawn wire specifications total compression rate is less than the required times drawing, can throw a drawing. Rejection mode principles: Inlet is small, outlet is fine, then dumped in front of passes; Inlet is big, outlet is rough, then throw behind the times. When the need dumped mold, the steel wire after the need to jump-mode machine mode box, and then into the next need to pull the mold box so that the wire can be within the effective stroke of the arm swing, thus ensuring the sensor can detect and adjust to match adjacent reel speed.

6. Capstan cooling: Inside of the capstan use narrow slit water cooling, cooling ring fixed in the body, capstan run through the spindle, when the water flow at high speed, during which water turbulence, and emitted from the narrow gap high-speed, high heat transfer efficiency, so that the rolls to cool; outside of the capstan use wind cooling by fan. Capstan tilt installation, increase the capstan product wire to extend the wire and the air heat exchange time.

7. Mold cooling: Drawing Die use open direct water-cooled, adjust the inlet valve to control the water height, when you need to replace the wire drawing dies, close the inlet valve, fast water emptying, and then change the mode, before and after the wire drawing dies, seals available copper pad or aluminum pad.

High speed pulley wire drawing machine packing and shipment-1.jpg


FAQ

1. Q:What is your minimum order quantity, can you send me samples?

A:Our minimum quantity is 1 set, as our product is machinery equipment, it’s difficult to send you samples, however, we can send you catalog, warmly welcome you to come visit our company. 

2. Q:Which level of quality are your products?

A:We have got CE, ISO, SGS, TUV, SONCAP certificate so far. 

3. Q:What is the delivery time of your machine?

A:In general, the delivery time of our machine is about 30 days, customized machine will be delivered as the negotiation with our clients. 

4. Q:Can the machine be customized as our need, such as put on our logo?

A:Surely our machine can be customized as your need, Put on your logo is also available. 

5. Q:As the shipping period will take long time, how can you make sure the machine won’t be broken?

A:Our machine is PE film wrapped, to make sure the machine can be delivered to our customer smoothly, we will use the steel wire to fix the machine with the container., 

6. Q: May i know which payment will be accepted by your company?

A:So far 100%T/T before shipment, and 30% deposit paid by T/T, balance paid by L/C are available.

Our factory.jpg

Should you're in need of quality and stable high speed copper plated wire drawing machine made in China, welcome to buy the machine from our factory. We are one of the leading such manufacturers and suppliers in China, equipped with advanced equipment and technology. Welcome to contact us.

Related Products

Feedback

Products List