We've been fully committed to offering our consumers with competitively priced good quality merchandise, prompt delivery and professional support for gold wire drawing machine, wire drawing machine design, wire drawing reduction formula. Our team members are aim to provides products with high performance cost ratio to our customers, and the goal for all of us is to satisfy our consumers from all over the world. We realize that the fundamental condition for the development of our business is to win customers' satisfaction by pursuing first-class quality, reasonable price, strict delivery time and considerate service. We firmly believe that the trust and respect paid in return must be a sense of responsibility and mission. Please feel cost-free to speak to us for small business and we believe we'll share the best trading experience with all our merchants.
Straight line drawing machine introduction
Wandeshun Machine is one of the leading wire drawing machine manufacturers in China , is specialized in various manufacturing wire drawing machines, have already been exported to Vietnam , Indonesia, Uzbekistan Kenya, South Africa, Algeria, Egypt, Iran, Turkey and so on.
Product parameters
Product process
1. Drive: Host straight line wire drawing machine, the first five heads power by the AC frequency motor through high-frequency joint narrow V-belts, spread by the hardened reducer to capstan. And the other six heads power by the AC frequency motor through two high-frequency joint narrow V-belt to capstan.
2. Brake: Clamp brake mounted on the motor pulley, quick stop or emergency stop wire drawing machine, which can effectively brake. Its role not only as a brake, but also to prevent the reel reverse brake, release the clip close to the solenoid valve control clamp brake cylinder.
3. Capstan: The material is ZG45 steel, surface is build-up welded, the surface is brightness, smooth, wear-resistant surfacing height of 150mm, long service life; hub height of 150-200mm.
4. Drawing die box: Die box is welded structure, into two cavity. The guide roller is mounted into the side to ensure that steel wire can straight into the drawing die, die holder should be adjusted to wire tangent to enter the drawing rolls tuning roller installed at the entry end of the mold base tuning roll by a small cylinder put power, tuning the swing of the roller, so that the corresponding sensor output signal to fine-tune the speed of change. Tuning roller wire tension by adjusting the air pressure change, regulation range 0.15-0.6Mpa. The mold box is also equipped with a stirring device. Tuning roller side of the mold box, a gear reducer single-phase capacitance running motor through a sprocket, power passed to the stirring arm to stir the mold box, lubrication powder, without agglomeration affect lubrication.
5. Jump-mode device: When drawn wire specifications total compression rate is less than the required times drawing, can throw a drawing. Rejection mode principles: Inlet is small, outlet is fine, then dumped in front of passes; Inlet is big, outlet is rough, then throw behind the times. When the need dumped mold, the steel wire after the need to jump-mode machine mode box, and then into the next need to pull the mold box so that the wire can be within the effective stroke of the arm swing, thus ensuring the sensor can detect and adjust to match adjacent reel speed.
6. Capstan cooling: Inside of the capstan use narrow slit water cooling, cooling ring fixed in the body, capstan run through the spindle, when the water flow at high speed, during which water turbulence, and emitted from the narrow gap high-speed, high heat transfer efficiency, so that the rolls to cool; outside of the capstan use wind cooling by fan. Capstan tilt installation, increase the capstan product wire to extend the wire and the air heat exchange time.
7. Mold cooling: Drawing Die use open direct water-cooled, adjust the inlet valve to control the water height, when you need to replace the wire drawing dies, close the inlet valve, fast water emptying, and then change the mode, before and after the wire drawing dies, seals available copper pad or aluminum pad.
FAQ
1. Are you a manufacturer, trading company or a third party?
We are a manufacturer, and we have builded up our company since 1998.
2. Where is your factory located?
Our factory address is : Address: (Yangjiawan Village) Phase5, Shuofang Industrial Park,
New Area, Wuxi, Jiangsu, China.
3. How can i get to your factory?
Our factory is near WUXI Airport, we can pick you up in the airport.
4. If i will need to stay in your place for few days, is that possible to book the hotel for me?
It’s always my pleasure, hotel booking service is available.
5. What is your minimum order quantity, can you send me samples?
Our minimum quantity is 1 set, as our product is machinery equipment, it’s difficult to send you samples, however, we can send you catalog, warmly welcome you to come visit our company.
6. Which level of quality are your products?
We have got CE, ISO, SGS, TUV, SONCAP certificate so far.
Packaging and Transportation
In the process of seeking cooperation, we are not blindly pursuing economic benefits but strive to solve the actual needs of customers with intrinsic specific value of the Straight Line Low/Mild Carbon/Stainless Steel Wire Drawing Machine Manufacturer itself. With the rapid development of cutting-edge manufacturing technology and modern information technology, the customization of products was pushed forward at high speed. Our company considers quality as its lifespan, and sees real customer interests and our long-term development as one.
Hot Tags: High Speed Low Carbon Straight Line Wire Drawing Machines, China, manufacturers, suppliers, factory, made in China, copper wire bunching machine, automatic roofing nail making machine, Wire Drawing Machine technological process, Dry wire drawing machine, low carbon steel wire drawing machine, drawing machine for wire
