We believe that when customers buy our Blocker Wire Drawing Machine, carbon steel wire drawing machine, Drawing machine and Welding machine, they do not only value our products for cheapness, but also because they purchase our company's products and services to achieve value added. Our hugely specialized process eliminates the component failure and offers our consumers unvarying high quality, allowing us to control cost, plan capacity and maintain consistent on time delivery. Due to the pursuit of quality, our company has established a number of high standard production bases to comprehensively improve the on-site management level and provide strong guarantee for product quality. Our quality management strategy shows that the creation, protection and development of our brand depend on the trust and praise of customers in product quality.
Horizontal wire drawing machine introduction
Wandeshun Machine is one of the leading wire drawing machine manufacturers in China , is specialized in various manufacturing wire drawing machines, have already been exported to Vietnam , Indonesia, Uzbekistan Kenya, South Africa, Algeria, Egypt, Iran, Turkey and so on.
Product parameters
Product process
1. Drive: Host straight line wire drawing machine, the first five heads power by the AC frequency motor through high-frequency joint narrow V-belts, spread by the hardened reducer to capstan. And the other six heads power by the AC frequency motor through two high-frequency joint narrow V-belt to capstan.
2. Brake: Clamp brake mounted on the motor pulley, quick stop or emergency stop wire drawing machine, which can effectively brake. Its role not only as a brake, but also to prevent the reel reverse brake, release the clip close to the solenoid valve control clamp brake cylinder.
3. Capstan: The material is ZG45 steel, surface is build-up welded, the surface is brightness, smooth, wear-resistant surfacing height of 150mm, long service life; hub height of 150-200mm.
4. Drawing die box: Die box is welded structure, into two cavity. The guide roller is mounted into the side to ensure that steel wire can straight into the drawing die, die holder should be adjusted to wire tangent to enter the drawing rolls tuning roller installed at the entry end of the mold base tuning roll by a small cylinder put power, tuning the swing of the roller, so that the corresponding sensor output signal to fine-tune the speed of change. Tuning roller wire tension by adjusting the air pressure change, regulation range 0.15-0.6Mpa. The mold box is also equipped with a stirring device. Tuning roller side of the mold box, a gear reducer single-phase capacitance running motor through a sprocket, power passed to the stirring arm to stir the mold box, lubrication powder, without agglomeration affect lubrication.
5. Jump-mode device: When drawn wire specifications total compression rate is less than the required times drawing, can throw a drawing. Rejection mode principles: Inlet is small, outlet is fine, then dumped in front of passes; Inlet is big, outlet is rough, then throw behind the times. When the need dumped mold, the steel wire after the need to jump-mode machine mode box, and then into the next need to pull the mold box so that the wire can be within the effective stroke of the arm swing, thus ensuring the sensor can detect and adjust to match adjacent reel speed.
6. Capstan cooling: Inside of the capstan use narrow slit water cooling, cooling ring fixed in the body, capstan run through the spindle, when the water flow at high speed, during which water turbulence, and emitted from the narrow gap high-speed, high heat transfer efficiency, so that the rolls to cool; outside of the capstan use wind cooling by fan. Capstan tilt installation, increase the capstan product wire to extend the wire and the air heat exchange time.
7. Mold cooling: Drawing Die use open direct water-cooled, adjust the inlet valve to control the water height, when you need to replace the wire drawing dies, close the inlet valve, fast water emptying, and then change the mode, before and after the wire drawing dies, seals available copper pad or aluminum pad.
OUR SERVICE
●We provide free technical service about casting parts and application issues.
●Free on-site touring and introduction of our factory
●We provide process design and validation for free
●We can guarantee on-time delivery of samples and goods
●Close follow-up of all orders by special person and keep customers informed timely
●All after-sale request will be responded in 24 hours
FAQ
1. Q：As the shipping period will take long time, how can you make sure the machine won’t be broken?
A：Our machine is PE film wrapped, to make sure the machine can be delivered to our customer smoothly, we will use the steel wire to fix the machine with the container.,
2. Q： May i know which payment will be accepted by your company?
A：So far 100%T/T before shipment, and 30% deposit paid by T/T, balance paid by L/C are available.
3. Q：About the after-sale service, how can you solve the problems occurred of your overseas customer in time?
A：The warranty of our machine is normally 12 months, during this period, we will arrange the international express immediately, to make sure the replace parts to be delivered as soon as possible.
4. Q：After we placing an order, will you arrange the installation of the machine at present?
A：All the machines will be tested well before delivered, so almost of them can be used directly, also our machine are easy to be installed, if you customer needs our assistance, we will be pleased to arrange the installation, but all the cost will be be charged by you.
5. Q：How can i get the after-service?
A：We will send you the spare parts by free if the problems caused by us.If it is the men-made problems,we also send the spare parts,however it is charged. Any problem, you can call us directly.
6. Q：How can i trust your company?
A：With 10-years-professional design, we can provide you suitable suggestion and lowest price
Assessed by third party, national patents and CE, ISO for all equipment.
Our Customers
Please feel free to send us your detailed requirements, you would be satisfied with our service.
Contact Below:
Wuxi Wandeshun Machine Co., Ltd
Add:Phase5, Shuofang Industrial Park, New Area, Wuxi, Jiangsu, China
Tel:86-510-85260990
Mobile:86-13921534531
86-13806184032
86-13915322227
Fax:86-510-85261990
Email:sales01@wxwds.com
Our company specializes in Electrical Aerial Bundled Cable. ABC Cable with PVC XLPE Insulated. products, and is a professional and large-scale manufacturer and service provider with strong competitiveness in this industry in China. Since our company focuses on team building, we have a production team, a mature design team, as well as a enthusiastic sales team. The spirit of enterprise is serious, hardworking, sincere and goodwill, and the code of conduct is to be a good person, do good things, work with a career attitude, have a strong sense of responsibility and enterprising spirit, and be diligent in learning.
Hot Tags: horizontal wire drawing machine low carbon wire drawing machine, China, manufacturers, suppliers, factory, made in China, OTO Type Dry Wire Drawing Machine, copper wire drawing Machinery, Pulley Type Dry Wire Drawing Machine, wire making machine, Tube drawing machines, stranding machine
