Our company will continue to provide you with high quality super enamelled copper wire drawing machine, Nail making machine auxiliary equipment, Multiwire drawing machine and perfect service, and sincerely welcome foreign customers to negotiate business with us and carry out fruitful cooperation. During the business, we want to become an indispensable partner and supporter in the development of your business. A set of scientific management system, exquisite production technology and excellent manufacturing equipment have established the high standard of product quality of our company, which makes us develop in continuous improvement. Until now our merchandise are now moving on fast and very popular all over the world. We sincerely hope that we can establish long-term and stable cooperative relations with customers at home and abroad on the basis of mutual benefit and common development.
Straight line drawing machine introduction
Wandeshun Machine is one of the leading wire drawing machine manufacturers in China , is specialized in various manufacturing wire drawing machines, have already been exported to Vietnam , Indonesia, Uzbekistan Kenya, South Africa, Algeria, Egypt, Iran, Turkey and so on.
Product parameters
Product process
1. Drive: Host straight line wire drawing machine, the first five heads power by the AC frequency motor through high-frequency joint narrow V-belts, spread by the hardened reducer to capstan. And the other six heads power by the AC frequency motor through two high-frequency joint narrow V-belt to capstan.
2. Brake: Clamp brake mounted on the motor pulley, quick stop or emergency stop wire drawing machine, which can effectively brake. Its role not only as a brake, but also to prevent the reel reverse brake, release the clip close to the solenoid valve control clamp brake cylinder.
3. Capstan: The material is ZG45 steel, surface is build-up welded, the surface is brightness, smooth, wear-resistant surfacing height of 150mm, long service life; hub height of 150-200mm.
4. Drawing die box: Die box is welded structure, into two cavity. The guide roller is mounted into the side to ensure that steel wire can straight into the drawing die, die holder should be adjusted to wire tangent to enter the drawing rolls tuning roller installed at the entry end of the mold base tuning roll by a small cylinder put power, tuning the swing of the roller, so that the corresponding sensor output signal to fine-tune the speed of change. Tuning roller wire tension by adjusting the air pressure change, regulation range 0.15-0.6Mpa. The mold box is also equipped with a stirring device. Tuning roller side of the mold box, a gear reducer single-phase capacitance running motor through a sprocket, power passed to the stirring arm to stir the mold box, lubrication powder, without agglomeration affect lubrication.
5. Jump-mode device: When drawn wire specifications total compression rate is less than the required times drawing, can throw a drawing. Rejection mode principles: Inlet is small, outlet is fine, then dumped in front of passes; Inlet is big, outlet is rough, then throw behind the times. When the need dumped mold, the steel wire after the need to jump-mode machine mode box, and then into the next need to pull the mold box so that the wire can be within the effective stroke of the arm swing, thus ensuring the sensor can detect and adjust to match adjacent reel speed.
6. Capstan cooling: Inside of the capstan use narrow slit water cooling, cooling ring fixed in the body, capstan run through the spindle, when the water flow at high speed, during which water turbulence, and emitted from the narrow gap high-speed, high heat transfer efficiency, so that the rolls to cool; outside of the capstan use wind cooling by fan. Capstan tilt installation, increase the capstan product wire to extend the wire and the air heat exchange time.
7. Mold cooling: Drawing Die use open direct water-cooled, adjust the inlet valve to control the water height, when you need to replace the wire drawing dies, close the inlet valve, fast water emptying, and then change the mode, before and after the wire drawing dies, seals available copper pad or aluminum pad.
FAQ
1. Are you a manufacturer, trading company or a third party?
We are a manufacturer, and we have builded up our company since 1998.
2. Where is your factory located?
Our factory address is : Address: (Yangjiawan Village) Phase5, Shuofang Industrial Park,
New Area, Wuxi, Jiangsu, China.
3. How can i get to your factory?
Our factory is near WUXI Airport, we can pick you up in the airport.
4. If i will need to stay in your place for few days, is that possible to book the hotel for me?
It’s always my pleasure, hotel booking service is available.
5. What is your minimum order quantity, can you send me samples?
Our minimum quantity is 1 set, as our product is machinery equipment, it’s difficult to send you samples, however, we can send you catalog, warmly welcome you to come visit our company.
6. Which level of quality are your products?
We have got CE, ISO, SGS, TUV, SONCAP certificate so far.
Packaging and Transportation
'Based on domestic market and expand overseas business' is our improvement strategy for Cheap Wholesale Straight Pulley Line Wire Drawing Machine Production Line. We have built a solid reputation for satisfying and exceeding customer expectations. Our manufacturing process is quality controlled, and we only use the best materials and components to make our products. We are looking forward to cooperating with you! We have rich experience in process, material, product quality and service management.
Hot Tags: High Speed Low Carbon Straight Line Wire Drawing Machines, China, manufacturers, suppliers, factory, made in China, automatic cutting machine, cable drawing machine, wire drawing machine pdf, automatic copper wire drawing machine, wafios straightening and cutting machine, Water Type Wire Drawing Machine
